時間：2023-04-25 15:27:06（部分內容來源于網絡，不代表本站觀點）

卷?yè)P(yáng)啟閉機用來啟閉較重的閘門
The winch hoist is used to open and close heavier gates
卷?yè)P(yáng)啟閉機機適用于各種較重噸位的閘門以及液壓工程閘門的啟閉。它可用于平原或山區有無電源。產品主要由電機、聯軸器、傳動軸、減速器、交流制動器、開式齒輪、鼓形件、皮帶輪系列件、電控箱、負載控制器、手搖臂、齒條組等組成。對。結構緊湊，承載能力大，運行穩定可靠，安裝維護方便，設計合理。隨著距離的增型槽模具 一次性止血帶 保定水處理設備 一次性止血帶 保定空壓機 北京真空泵加，產品可配備三體式或傳動軸軸承。
The winch hoist is suitable for the opening and closing of various heavy tonnage gates and hydraulic engineering gates. It can be used for plains or mountainous areas with or without power supply. The product mainly consists of motors, couplings, transmission shafts, reducers, AC brakes, open gears, drum parts, pulley series parts, electric control boxes, load controllers, hand rocker arms, gear racks, etc. yes. Compact structure, large load-bearing capacity, stable and reliable operation, convenient installation and maintenance, and reasonable design. As the distance increases, the product can be equipped with three body or transmission shaft bearings.
卷?yè)P(yáng)啟閉機在安裝與調試時需要注意：
When installing and debugging the winch hoist, attention should be paid to:
1、安裝起重葫蘆時，底座的基礎應牢固、平整，留出腳螺釘?shù)奈恢谩Ｉ禉C(jī)到位后，地基應平整并澆灌。
1. When installing the lifting hoist, the foundation of the base should be firm and flat, leaving a space for the foot screws. After the elevator is in place, the foundation should be leveled and poured.
2、首先，鋼絲繩纏繞在平衡輪上。鋼絲繩的長度在兩邊都是等分的。鋼絲繩由活動滑輪組纏繞，鋼絲繩的端部固定在滾筒的端部。
2. Firstly, the steel wire rope is wrapped around the balancing wheel. The length of the steel wire rope is equally divided on both sides. The steel wire rope is wound by a movable pulley block, and the end of the steel wire rope is fixed at the end of the drum.
3、在空載情況下，確保三相電流不平衡不超過正負10%，并測量電流值。
3. Under no-load conditions, ensure that the three-phase current imbalance does not exceed plus or minus 10%, and measure the current value.
4、上下限位調整：當閘門完全關閉時，按下行程開關的上限并將其固定在螺絲上。當閘門完全打開時，下限板壓下沖程開關并固定在螺桿上。
4. Upper and lower limit adjustment: When the gate is fully closed, press the upper limit of the travel switch and fix it on the screw. When the gate is fully open, the lower limit plate presses down on the stroke switch and fixes it on the screw.